Cutting Tool

Word CUTTING TOOL
Character 12
Hyphenation N/A
Pronunciations N/A

Definitions and meanings of "Cutting Tool"

What do we mean by cutting tool?

Here you will find one or more explanations in English for the word cutting-tool. Define cutting-tool, cutting-tool synonyms, cutting-tool pronunciation, cutting-tool translation, English dictionary definition of cutting-tool.

Synonyms and Antonyms for Cutting Tool

  • Synonyms for cutting tool
  • Cutting Tool synonyms not found!!!
  • Antonyms for cutting tool
  • Cutting Tool antonyms not found!

The word "cutting-tool" in example sentences

Since the beginning of 2006, Berkshire has spent nearly $17 billion buying private companies lock, stock and barrel, including an Israeli cutting-tool maker and a distributor of electronic components. ❋ Unknown (2008)

The shank is often made of mild steel in order to save valuable cutting-tool material (high-speed steel) or because the properties of other cutting-tool materials (hard metals, ceramic cutting-tool materials, diamonds) require this. ❋ Horst Kth (1990)

In the whole line of tools which the machinist must take care of daily, there is nothing as important as the lathe cutting-tool, and the knowledge which goes with it to use the proper one. ❋ J. S. Zerbe (N/A)

The upper surface of this fuze is graduated into seconds and fourths of seconds; and it is only necessary to lay bare the composition contained in the fuze, by the cutting-tool, to prepare the projectile for instant use. ❋ United States. Navy Dept. Bureau Of Ordnance (N/A)

One hollow is cut during each forward travel of the carriage; and, when such travel is finished, a cam-disk, p, placed on the shaft, n, lifts the tool-carrier, b, and thus draws the cutting-tool out of the hollow cut by it, so that the carriage cam can then move back without restraint. ❋ Various (N/A)

The cutting-tool and stylus are devices made of sapphire, a gem next in hardness to a diamond, and they have to be cut and formed to an exact nicety by means of diamond dust, most of the work being performed under high-powered microscopes. ❋ Unknown (1910)

It was early recognized that a single needle for forming the record and the reproduction therefrom was an undesirable arrangement, since the formation of the record required a very sharp cutting-tool, while satisfactory and repeated reproduction suggested the use of a stylus which would result in the minimum wear. ❋ Unknown (1910)

Another important change was in the nature of a reversal of the original arrangement, the cylinder or mandrel carrying the record being mounted in fixed bearings, and the recording or reproducing device being fed lengthwise, like the cutting-tool of a lathe, as the blank or record was rotated. ❋ Unknown (1910)

The minute proportions of these devices will be apparent by a glance at the accompanying illustrations, in which the object on the left represents a common pin, and the objects on the right the cutting-tool and reproducing stylus, all actual sizes. ❋ Unknown (1910)

Instead of tin-foil, a wax cylinder is employed, the record being cut thereon by a cutting-tool attached to a diaphragm, while the reproduction is effected by means of a blunt stylus similarly attached. ❋ Unknown (1910)

Instead of tin-foil, a wax cylinder is employed, the record being cut thereon by a cutting-tool attached to a diaphragm, while the reproduction is effected by means of ❋ Frank Lewis Dyer (1905)

The principle of the machine was to carry a guide-point at one side over the bust or alto-relievo to be copied, and at the other side to carry a corresponding cutting-tool or drill over the alabaster, ivory, jet, or plaster of Paris to be executed. ❋ Samuel Smiles (1858)

If a piece of metal is to be cut in a lathe, for example, there is one particular angle at which the cutting-tool must be held to insure the cleanest cut; and it is quite natural that the idea of fixing the tool at that angle should present itself to an intelligent workman. ❋ Charles Babbage (1831)

The Korean government lodged the complaint at the WTO in November 2009 at the request of Posco, the world's third-biggest steelmaker, and domestic cutting-tool manufacturers. ❋ Unknown (2011)

With a view to streamlining its cutting-tool ordering system, reducing inventory levels and cutting tool use, Benham Manufacturing recently undertook a review of its entire tooling structure and process-optimisation techniques. ❋ Unknown (2010)

Managed by a local Iscar distributor, Matrix is a computerised total-management system that can give users absolute control over their cutting-tool inventory, streamline purchasing functions and drive down costs. ❋ Unknown (2010)

Cross Reference for Cutting Tool

  • Cutting Tool cross reference not found!

What does cutting tool mean?

Best Free Book Reviews
Best IOS App Reviews